FARGO DTC515 MANUAL PDF

FARGO DTC515 MANUAL PDF

FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, 10 Cleaning Cards, 10 Cleaning Pads, 10 cleaning tapes, full instructions. FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, DTC/ Dual hopper; PVC cards “); auto or manual feed. HID GLOBAL, HID, the HID logo, FARGO, and iCLASS, are .. installed and used in accordance with the instruction manual, may cause.

Author: Mezitilar Vudojas
Country: Botswana
Language: English (Spanish)
Genre: Health and Food
Published (Last): 16 April 2008
Pages: 425
PDF File Size: 7.9 Mb
ePub File Size: 7.75 Mb
ISBN: 790-6-91014-648-9
Downloads: 91355
Price: Free* [*Free Regsitration Required]
Uploader: Arashill

Fargo DTC500 Specifications

Remove the two mounting screws at the middle and lower section along the left edge of the circuit board. Replacing The Headlift Motor a Motor to the front faggo plate.

If a Program Exception is displayed again, continue to step 2.

Move the slide to the right to cause more heat to be used, thus generating a darker print. Remove any debris that may be inside. Choose from these five categories: Release the plastic tabs in the four corners of the cover.

Select this option to cause the Printer to dispense with the mqnual job if a blank card is removed or ejected.

See Using the Image Position button on page This test print procedure can be helpful in ensuring a that the computer is effectively communicating with the Printer, and b that the Printer is functioning properly. If there is not sufficient resistance, replace the U-shaped spring on rtc515 back of the Flipper Table.

  ASTM F756 PDF

Replacing The Main Board d 3 Circuit Board mounting screws located at the left, middle and right sections. Scratch-Off Resin Ribbon, prints. Do not change this setting.

FARGO ELECTRONICS DTC SERIES TROUBLESHOOTING MANUAL Pdf Download.

Internal Card Guide always remains parallel to the card path and that the screws loosened in Step 1 are retightened after each adjustment. See the Updating the Printer’s Firmware on page Ensure that the guide belt for the Hopper Travel Assembly D is intact and moves smoothly.

The only caution when using this feature is that cards must be loaded properly.

DTC resin ribbons feature RFID technology which tells you how many prints remain on your print ribbon and if your ribbon is running low. The error log will stop logging errors once it has reached its error occurrence limit of When you remove the Printhead, you can see the circled area, as shown in the photo below. Use the Image Position controls to adjust the position of the overall print area to be precisely centered on a card.

Specifying the Copies Specifies the number of copies to be printed, as shown above. To order additional materials, please contact your authorized reseller. Comments to this Manuals Your Name.

The Printer will feed, encode, and eject a card. Record the Magnetic TOF value on the test card last printed. Select Setup Printer and Encoder Settings. Switch Box or peripheral. Resolving an Upgrade Failed error continued See the previous procedure in this section. Dtc55 the Reset button to clear the entire existing error log and start a new log.

  LEONIS LE TALISMAN DES PHARAONS PDF

FARGO DTC SPECIFICATIONS Pdf Download.

Motor to the manuwl side plate. Mqnual can only be seen when you hold the Printhead, as shown here. Close the Print and Transfer Stations after the Rollers are clean and completely dry. Reviewing The Shift Data Left Select this option to shift the recorded magnetic data to the left-hand side of the card’s Magnetic Stripe. If the Start Sentinel is too close to the leading edge of the card, increase or make positive the Magnetic TOF setting needs.

Selecting the Defined Area s with the K Panel Resin tab Step Procedure Select the Defined Area s option to print the resin black K panel for all black found only in an area or areas defined, as shown below. Please specify with order. Each Firmware type has a different update process.

Be sure the Card Guide Rail always remains parallel to the card path and that the screws loosened in step 1 are retightened after each adjustment.